China Standard Model Lhy Vertical Heat Preservation Liquid Sulphur Pump shaft collar dimensions

Product Description

Model Lhy Vertical Heat Preservation Liquid Sulphur Pump
 

Product Description

Conform to design standard of 1S57158/GB5656 Flow range: 0.2~400m3/h
Lift range: ~150m
Design pressure: 1.6MPa Application temperature: ~500ºC
Application field: This series of pump is mainly used in sulphuric acid, pyrite acid sulfur recovery, coal chemical industry, petroleum cracking of sulfur recovery and other material need heat preservation conditions.

Summary
Sulfur pump with small flow capacity, high delivery lift, is developed on the strength of previous sulfur acid pump, coll aborated with institutes, colleges, it is characteristic of high delivery lift andsmall flow capacity, impossibly achieved by centrifugal pump, while unstable performance existing during operation of volute pump. There for, adopt latest hy draulic design, integrating unique advantages of centrifugal pump and volute pump. It has filled in domestic gap, reac hed international advanced level, able to substitute for impo ted ones, economizing relevant investment, widely used in acid making procedure to convey liquefied sulfur under 130-158ºC, with improvement, it also can be used under ot her hi – temperature and insulation working conditions.

Parameter range
Capacity:Q:0.2-400m3/h
Head:H:2-150m
Temperature:T:500ºC
Pressure:P:1.6MPa
Under water depth:L:0.5-5m

Meaning of model code
2-Capacity
120-Head
1-Under water depth
LHY-Feiyue Sulfur pump code

Chart

1 Before the pump cover 2 Impeller nut 3 Pump body 4 Impeller 5 Elbow 6 Under the collar
7 Bushing 8 Liquid pipe 9 Intermediate to take over 10 Pump shaft 11 Packing collar 12 Stuffing box
13 Packing gland 14 Bearing box 15 Bearing cover 16 Bearing 17 Bearing 18 Lock nut
19 Bearing cover 20 Electric frame 21 On taking over 22 Bushing gland 23 On the liner 24 Xihu (West Lake) Dis. bearing

1 Screen 2 Under the collar component 1 3 Entrance section 4 Impeller 4 5 Lock nut,bolt(4) 6 Xihu (West Lake) Dis. vane 4
7 Pump body 8 Balancing drum 9 Under the collar component 2 10 Take over(steam pipe) 11 Take 2 in the middle(steam pipe) 12 Intermediate shat sleeve component(2)
13 Middle bearing 14 Shaft 15 Among over 1(steam pipe) 16 Coupling collar 17 Coupling shaft snap ring 18 Intermediate to take over
19 On the shaft 20 Steam over 21 On taking over 22 Floor 23 Bearing box 24 Packing gland
25 On the shaft sleeve 1 26 Collar 2 27 Bearing 28 Bearing gland 29 Dowel pin coupling 30 Electric trame
31 Motor                    

Product Parameters

Performance parameters of the table

Company Profile

FAQ

Max.Head: 110m-150m
Max.Capacity: >400 L/min
Driving Type: Motor
Impeller Number: Single-Stage Pump
Working Pressure: Low Pressure Pump
Influent Type of Impeller: Single Suction Pump
Customization:
Available

|

Customized Request

Shaft Collar

How to Choose the Right Shaft Collar

A shaft collar is a small, inexpensive machine component that serves a variety of purposes in power transmission. It is most commonly used in gearboxes and motors. It can serve as a mechanical stop, bearing face, or locating component. Its simple design makes it easy to install. Here are some of the most common types and their functions.

Function

Shaft collars are an important part of many mechanical systems. These devices hold mechanical components on a shaft and also help mount shafts on flat surfaces. They are available in many different styles, sizes, and materials. Selecting the right shaft collar is essential in preventing damage to components. Stafford Manufacturing, a leading manufacturer of shaft collars and other related mechanical components, can help you choose the right one for your application.
There are two main types of shaft collars. The first is the Heavy Duty type. It has a larger outer diameter and wider opening. While this may seem to increase holding power, the problem with that is that it can reduce the amount of space the collar has on the shaft. On the other hand, the Thin Line type is similar, but is made with smaller outer diameters. Another type is the Threaded Bore shaft collar. These shaft collars offer exceptional axial holding power, and are designed to protect threaded shafts without causing any damage.
A shaft collar has many uses and is typically used in industrial applications. It can act as a spacer and to stop shaft movement in reciprocating applications. It can also be used to align and position parts of automation machinery.

Types

There are several different types of shaft collars. These components are critical for a variety of applications, and their design plays a large role in the performance of the resulting product. To select the most appropriate collar, designers must consider several factors, including the style, material, bore size, and geometry of the shaft. Many manufacturers provide performance data, and users can contact them for assistance.
There are many different types of shaft collars, which make it important to understand how each one works and what applications they can serve. Fortunately, shaft collars are easy to install and require little maintenance. Whether you need to secure industrial railings or position medical equipment, shaft collars are a versatile component that can be tailored to meet your needs.
One type of shaft collar is the locking collar. This type of shaft collar has a threaded end that is designed to mate with spindle bearings. They offer an increased TIR than standard shaft collars and allow for precise preload control. They also feature slots for spanner wrenches.
Shaft Collar

Sizes

Shaft collars come in a variety of sizes. You can get a small diameter shaft collar for small equipment, or a large diameter shaft collar for larger equipment. Both styles are made from solid steel, and they come in several thicknesses. You can choose between one-half inch and six-inch collars, depending on your needs.
There are no specific standards for shaft collars, but most manufacturers have similar designs. They’re either single-point faced or double-split, and can be fine or coarse threaded. They’re often used as mechanical stops, bearing faces, or as locating components. Their bore is either fine or coarse, and their outside diameter and width are determined by the shaft diameter.
Shaft collars are commonly found in mechanical and automation equipment. These ring-shaped devices hold motor components, sprockets, and bearings in place. They also allow them to be adjusted and positioned precisely. A shaft collar is often used to connect the end of a shaft to a mechanical stop.
Another type of shaft collar is called a set collar. It has a recessed area for a screw to bite into a shaft. These collars are perfect for holding sprocket hubs, bearings, and spacers. They can also be used as a rigid coupling.

Cost

When choosing a shaft collar, consider its intended application and cost. Some shaft collars are very expensive while others are quite affordable. Choose one that meets the needs of your assembly. If you’re using the shaft collar infrequently, a clamp style or a set screw style may be a better choice. Then, you can easily adjust or disassemble it with just a few tools. If you’re using it more frequently, choose a two-piece shaft collar.
The material of the shaft collar is also an important consideration. Steel and stainless steel are common choices. While both materials are strong and durable, steel tends to have better holding power. However, aluminum shaft collars are lighter and provide better strength-to-weight ratio. The type of material you choose depends on the amount of corrosion protection you need, and whether you’ll need the collar to resist extreme temperatures. If the shaft collar is going to be used in a hot environment, you may want to go with a titanium collar.
There are many different sizes and types of shaft collars. The type of collar you choose depends on the specific application and the system it’ll be used in. Consider the dimensions of your shaft, the material of the shaft, and the length of the shaft to find the right fit. If you’re not sure what size you need, ask a manufacturer for help.
Shaft Collar

Placement on shaft

In some applications, the placement of the shaft collar can be critical to the overall performance of the machine. The collar’s design must take many factors into account, including material, style, bore size, and shaft geometry. If a user is uncertain of the proper placement of their collar, they should refer to the manufacturer’s website for guidance.
While shaft collars may look simple, they’re actually essential mechanical components that are used in almost every type of machinery. Despite their ubiquitous use in every industry, they are often underappreciated due to their complexity. Many people aren’t aware of their importance or the various types of collars available. This shaft collar guide will provide detailed information to help you find the right shaft collar for your specific application.
The surface treatment of the shaft collar is another important factor that contributes to its holding power. The most common treatment is a black oxide finish. This finish enhances screw torque while preserving the frictional properties of the bore. This finish can be further optimized by applying light oil to the screw. Zinc plating is also a good option for shaft collars. This material offers better corrosion resistance, but can reduce holding power.

Clamp style

A clamp style shaft collar is a simple and effective tool for securing shafts in machine tools. Its two-piece design allows for quick and easy positioning adjustments and has greater holding power than set screw collars. In addition, its friction-based connection maintains ease of use and prevents shaft damage. This type of collar is also more corrosion resistant than set screw collars.
There are several different types of shaft collars, including single and double split collars. Single-piece clamp collars are anchored into the shaft with a single tangential screw, whereas double-piece collars are anchored to the shaft with two socket cap screws. The latter type provides more stability and axial holding power and is suitable for rotating assemblies. A single or double-piece clamp collar can also be threaded to allow for precise positioning along the shaft. Its internal threads also provide enhanced support for high axial loads and act as a positive mechanical stop.
There are different types of shaft collars, each with its own set of advantages and disadvantages. A set-screw collar may be preferred over a clamp-style shaft collar, but it’s not the only choice. A set-screw collar can severely mar the shaft and can prevent fine adjustments. However, it is a good idea to use the torque wrench when tightening a shaft collar.

Zinc plated

Zinc plated shaft collars are available in a variety of sizes. They are precision machined from cold finished steel bar stock and zinc plated for corrosion resistance. They are also very attractive. They are made in the USA. Whether you need a zinc-plated shaft collar for a simple repair or a more complicated installation, Lovejoy has the right solution for your needs.
The CZPT MSP-12-FZ two-piece shaft collar has a 12mm bore, 28mm OD, and 11mm width. Its clamp style design allows you to easily install and remove the shaft collar. It is easily adjustable and is stamped with the CZPT name.
China Standard Model Lhy Vertical Heat Preservation Liquid Sulphur Pump   shaft collar dimensionsChina Standard Model Lhy Vertical Heat Preservation Liquid Sulphur Pump   shaft collar dimensions
editor by CX 2023-11-13

Leave a Reply

Your email address will not be published. Required fields are marked *